2pcs Front Upper Ball Joints Steering Kit For Chrysler Dodge Plymouth K772

Package Includes: 2 x Part # FRONT UPPER BALL JOINT - K772 Fit For 1957 DESOTO FIRESWEEP All All 1957 DODGE CORONET All All 1957 DODGE CUSTOM All All 1957 DODGE LANCER All All 1957 DODGE SUBURBAN All All 1957 PLYMOUTH BELVEDERE All All 1957 PLYMOUTH FURY All All 1957 PLYMOUTH PLAZA All All 1957 PLYMOUTH SAVOY All All 1957 PLYMOUTH SUBURBAN All All 1958 CHRYSLER TOWN & COUNTRY 5.8L 8Cyl V (5802)(354) 1958 CHRYSLER WINDSOR All All 1958 DESOTO FIRESWEEP All All 1958 DODGE CORONET All All 1958 DODGE CUSTOM All All 1958 DODGE LANCER All All 1958 DODGE SUBURBAN All All 1958 PLYMOUTH BELVEDERE All All 1958 PLYMOUTH FURY All All 1958 PLYMOUTH PLAZA All All 1958 PLYMOUTH SAVOY All All 1958 PLYMOUTH SUBURBAN All All 1959 CHRYSLER TOWN & COUNTRY 6.3L 8Cyl V (6286)(383) 1959 CHRYSLER WINDSOR All All 1959 DESOTO FIRESWEEP All All 1959 DODGE CORONET All All 1959 DODGE CUSTOM All All 1959 DODGE LANCER All All 1959 DODGE SIERRA Base 1959 DODGE SIERRA Custom 1959 PLYMOUTH BELVEDERE All All 1959 PLYMOUTH FURY All All 1959 PLYMOUTH SAVOY All All 1959 PLYMOUTH SUBURBAN All All 1960 CHRYSLER TOWN & COUNTRY All All 1960 CHRYSLER WINDSOR All All 1960 DESOTO ADVENTURER All All 1960 DESOTO FIREFLITE All All 1960 DODGE DART All All 1960 DODGE MATADOR All All 1960 DODGE POLARA All All 1960 DODGE SENECA All All 1960 PLYMOUTH BELVEDERE All All 1960 PLYMOUTH FURY All All 1960 PLYMOUTH SAVOY All All 1960 PLYMOUTH SUBURBAN All All 1961 CHRYSLER NEWPORT All All 1961 CHRYSLER TOWN & COUNTRY All All 1961 CHRYSLER WINDSOR All All 1961 DESOTO DESOTO All All 1961 DODGE DART All All 1961 DODGE POLARA All All 1961 DODGE SENECA All All 1961 PLYMOUTH BELVEDERE All All 1961 PLYMOUTH FURY All All 1961 PLYMOUTH SAVOY All All 1961 PLYMOUTH SUBURBAN All All 1962 CHRYSLER 300 All All 1962 CHRYSLER NEWPORT All All 1962 CHRYSLER TOWN & COUNTRY All All 1962 DODGE CUSTOM All All 1962 DODGE DART All All 1962 DODGE POLARA All All 1962 PLYMOUTH BELVEDERE All All 1962 PLYMOUTH FLEET SPECIAL All All 1962 PLYMOUTH FURY All All 1962 PLYMOUTH SAVOY All All 1963 CHRYSLER 300 All All 1963 CHRYSLER NEW YORKER All All 1963 CHRYSLER NEWPORT All All 1963 CHRYSLER TOWN & COUNTRY All All 1963 DODGE 330 All All 1963 DODGE 440 All All 1963 DODGE 880 All All 1963 DODGE CUSTOM All All 1963 DODGE POLARA All All 1963 PLYMOUTH BELVEDERE All All 1963 PLYMOUTH FLEET SPECIAL All All 1963 PLYMOUTH FURY All All 1963 PLYMOUTH SAVOY All All Note 10 Year Warrantly Please make sure that whether the Kit fits your vehicle or not before placing order Some of the parts we have grease fittings while other parts come factory sealed. please don\'t worry, this does not affect the performance or quality of the parts Ball Joint Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty 1.Raise the vehicle and remove the front wheels 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket 5.Remove the bad or worn ball joint from the control arm 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool 7.Clean the cone connection Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary 11.Finally, carry out a test drive Frequently Asked Questions (1).How will I know that I have to renew my ball joint parts? Or replace them? If your ball joint fails, you will listen to a strange sound while driving. And that sound may help you to realize that your ball joint has failed and you have to renew them (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car (3).Are worn ball joints dangerous? Yes, it can be quite dangerous. Because, a worn ball joint causes suspension damage, inspection failure, and breakage of related parts It might make your front suspension come apart while driving, so the wheels move in whatever direction inertia takes them. That can lead to a fatal accident (4).What happens if I don\'t replace ball joints? (5).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new 1 after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card