4x New Front Upper Lower Ball Joints Fit For Dodge Ram 2500 3500 Van B350 B250

Fitting the Following vehicle: 1975 - 1980 DODGE B300 All Models w/Heavy Duty Suspension 1972 - 1974 DODGE B300 VAN All Models w/Heavy Duty Suspension 1981 - 1994 DODGE B350 All Models w/Heavy Duty Suspension 1995 - 1998 DODGE B3500 All Models w/Heavy Duty Suspension 1973 - 1980 DODGE CB300 All Models w/Heavy Duty Suspension 1975 - 1980 DODGE D200 All Models w/Heavy Duty Suspension 1972 - 1974 DODGE D200 PICKUP All Models w/Heavy Duty Suspension 1981 DODGE D250 All Models w/Heavy Duty Suspension 1975 - 1980 DODGE D300 All Models w/Heavy Duty Suspension 1972 - 1974 DODGE D300 PICKUP All Models w/Heavy Duty Suspension 1981 - 1993 DODGE D350 All Models w/Heavy Duty Suspension 1999 - 2000 DODGE RAM 2500 VAN All Models w/Heavy Duty Suspension 1999 - 2000 DODGE RAM 3500 VAN All Models w/Heavy Duty Suspension 1975 - 1980 PLYMOUTH PB300 All Models w/Heavy Duty Suspension 1974 PLYMOUTH PB300 VAN All Models w/Heavy Duty Suspension 1981 - 1983 PLYMOUTH PB350 All Models w/Heavy Duty Suspension Package Includes: 2x Front Lower Ball Joint (Heavy Duty Suspension) - K7053T 2x Front Upper Ball Joint (Heavy Duty Suspension) - K7082 Note Although some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts Please check above compatibility list to make sure it fits your vehicle Ball Joint Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty 1.Raise the vehicle and remove the front wheels 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket 5.Remove the bad or worn ball joint from the control arm 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool 7.Clean the cone connection Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary 11.Finally, carry out a test drive Frequently Asked Questions (1).How will I know that I have to renew my ball joint parts? Or replace them? If your ball joint fails, you will listen to a strange sound while driving. And that sound may help you to realize that your ball joint has failed and you have to renew them (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car (3).Are worn ball joints dangerous? Yes, it can be quite dangerous. Because, a worn ball joint causes suspension damage, inspection failure, and breakage of related parts It might make your front suspension come apart while driving, so the wheels move in whatever direction inertia takes them. That can lead to a fatal accident (4).What happens if I don\'t replace ball joints? (5).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new 1 after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card