Pair 2: New Front Lower Ball Joint K5 Blazer C10 G10 G20 P10 R10

Fitting the Following vehicle: 1971-1974 | CHEVROLET | BLAZER | RWD 1975-1986 | CHEVROLET | C10 1971-1974 | CHEVROLET | C10 PICKUP 1971-1986 | CHEVROLET | C10 SUBURBAN 1975-1995 | CHEVROLET | G10 1971-1974 | CHEVROLET | G10 VAN 1975-1995 | CHEVROLET | G20 1973-1974 | CHEVROLET | G20 VAN 1975-1982 | CHEVROLET | K5 BLAZER | RWD 1975-1980 | CHEVROLET | P10 1971-1974 | CHEVROLET | P10 VAN 1987 | CHEVROLET | R10 1987-1988 | CHEVROLET | R10 SUBURBAN 1989-1991 | CHEVROLET | R1500 SUBURBAN 1975-1978 | GMC | C15 1975-1978 | GMC | C15 SUBURBAN 1971-1974 | GMC | C15/C1500 PICKUP 1971-1974 | GMC | C15/C1500 SUBURBAN 1979-1986 | GMC | C1500 1979-1986 | GMC | C1500 SUBURBAN 1975-1978 | GMC | G15 1971-1974 | GMC | G15/G1500 VAN 1979-1995 | GMC | G1500 1975-1978 | GMC | G25 1973-1974 | GMC | G25/G2500 VAN 1979-1995 | GMC | G2500 1971-1982 | GMC | JIMMY | RWD 1975-1978 | GMC | P15 1971-1974 | GMC | P15/P1500 VAN 1979-1980 | GMC | P1500 1987 | GMC | R1500 1987-1991 | GMC | R1500 SUBURBAN Package Includes: 2x Front Lower Ball Joint K6117T Note Although some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts Please check above compatibility list to make sure it fits your vehicle Ball Joint Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty 1.Raise the vehicle and remove the front wheels 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket 5.Remove the bad or worn ball joint from the control arm 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool 7.Clean the cone connection Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary 11.Finally, carry out a test drive Frequently Asked Questions (1).How will I know that I have to renew my ball joint parts? Or replace them? If your ball joint fails, you will listen to a strange sound while driving. And that sound may help you to realize that your ball joint has failed and you have to renew them (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car (3).Are worn ball joints dangerous? Yes, it can be quite dangerous. Because, a worn ball joint causes suspension damage, inspection failure, and breakage of related parts It might make your front suspension come apart while driving, so the wheels move in whatever direction inertia takes them. That can lead to a fatal accident (4).What happens if I don\'t replace ball joints? (5).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new 1 after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card