Steering 10x Front Control Arms Rear Sway Bar Links Part For 2003-2004 Murano

Fit For 2003 - 2004 Nissan MURANO All Models Package Includes: 1x Part# Front Lower Left (Driver) Control Arm + Ball Joint - K620558 1x Part# Front Lower Right (Passenger) Control Arm + Ball Joint - K620559 2x Part# Front Inner Tie Rods Ends - EV80625 2x Part# Front Outer Tie Rods Ends - ES80624 1x Part# Front Stabilizer/Sway Bar End Link (Driver) - K80255 1x Part# Front Stabilizer/Sway Bar End Link (Passenger) - K80256 1x Part# Rear Stabilizer/Sway Bar End Link (Passenger) - K80465 1x Part# Rear Stabilizer/Sway Bar End Link (Driver) - K80466 Notes Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty 1.Raise the vehicle and remove the front wheels 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket 5.Remove the bad or worn ball joint from the control arm 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool 7.Clean the cone connection Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary 11.Finally, carry out a test drive Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads (3).Stronger inclination of the vehicle during cornering If the sway bar stabilizer link is found to be defective, it should be replaced as described below 1.Raise vehicle and remove front wheels Tip:Always check both stabilizer links and replace them in pairs if necessary 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove Tip:If the ball stud also starts to turn, hold it with a suitable tool 4.Press stabilizer link out of torsion bar 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it 6.Press stabilizer link at suspension strut out of bracket 7.Insert new stabilizer link at suspension strut 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer Tip:Secure the ball stud against twisting with a suitable tool 9.Insert new stabilizer link at stabilizer 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension 12.Conclude with a test drive Tie-Rod End Replacement Guideline: This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance 1.Lift the vehicle and dismount the front axle wheels 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes 3.Dismount the front underride guard 4.Loosen the fastening nut from the tie rod and remove it completely 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator 6.Remove the clamp of the bellow on the steering gear 7.Push the bellow towards the tie rod end 8.Unscrew the inner tie rod from the rack 9.Clean the sealing face of the bellow at the steering gear 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle Note:Always use new self-locking nuts and bolts for a reliable repair 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer 12.Mount the bellow and close the clamps with the appropriate special tool Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure 14.Mount the front underride guard 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications 17.Perform a test drive Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car (3).What happens if I don\'t replace ball joints? (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new 1 after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card (5).Why should I get my tie rods inspected on a regular basis? (6).Vibrations (7).Shaking (8).Wandering (9).What are the symptoms of a bad sway bar? (10).What happens when a sway bar breaks?